Date of publication: 2017-11-28 04:54
ENGINE TOP END 5-81 Valves Operating Procedures x2522 Clean the seat area carefully. x2522 Coat the seat with machinist x2519 s dye. x2522 Fit a 95 xB5 cutter into the holder and slide it into the valve guide. x2522 Press down lightly on the handle and turn it right or left. Grind the seating surface only until it is smooth.
Does Kawi say, or is it assumed by the experts, that this bike 8217 s trellis frame is 8225 trickle-down 8221 tech from the H2? I think a lot of riders are hoping the H2 8217 s forced induction, or something like it, will also trickle down.
8-6 ENGINE REMOVAL/INSTALLATION Engine Removal/Installation x2522 Remove the engine sprocket [A] (see Engine Sprocket Removal in the Final Drive chapter). x2522 Disconnect: Crankshaft Sensor Lead Connector and Oil Pressure Switch Lead Terminal (see Crankshaft Sensor Removal in the Electrical System chapter) Starter Motor Cable (see Starter Motor Removal in the Electrical System chapter) Alternator Lead Connector (see Alternator Cover Re-.
9-22 CRANKSHAFT/TRANSMISSION Crankshaft and Connecting Rods x2522 Measure the connecting rod big end inside diameter, and mark each connecting rod big end in accordance with the inside diameter. x2522 Tighten the connecting rod big end nuts to the specified torque (see Connecting Rod Installation). NOTE x25CB .
PERIODIC MAINTENANCE 2-59 Periodic Maintenance Procedures x2522 Set the dimmer switch to high beam position. x2522 The low beam [A] and high beam [B] headlights should go on. x2522 The blue high beam indicator light (LED) [C] should go on. If the high beam headlight and/or blue high beam indicator light (LED) does not go on, inspect or replace the following item.
ELECTRICAL SYSTEM 16-67 Air Switching Valve Air Switching Valve Circuit 1. Ignition Switch 2. Joint Connector E 8. ECU 9. Frame Ground 9 5. Engine Ground 6. Battery 12 V 8 Ah 7. Starter Relay 8. Main Fuse 85 A 9.
SUSPENSION 18-7 Exploded View Torque Fastener Remarks N xB7 m kgf xB7 m ft xB7 lb Swingarm Pivot Shaft Nut Swingarm Pivot Shaft 87 in xB7 lb Swingarm Pivot Shaft Locknut Rear Shock Absorber Nut (Upper) Rear Shock Absorber Nut (Lower) Rocker Arm Nut Tie-Rod Nuts 8.
CRANKSHAFT/TRANSMISSION 9-9 Crankcase Splitting Crankcase Splitting x2522 Remove the engine (see Engine Removal in the Engine Removal/Installation chapter). x2522 Set the engine on a clean surface and hold the engine steady while parts are being removed. x2522 Remove: Oil Pressure Switch Terminal (see Oil Pressure Switch Removal in the Engine Lubrication System chapter) Crankshaft Sensor (see Crankshaft Sensor Removal in the Electrical System chapter)
FUEL SYSTEM (DFI) 8-115 Fuel Pump Fuel Pump Removal WARNING Gasoline is extremely flammable and can be explo- sive under certain conditions, creating the potential for serious burns. Make sure the area is well venti- lated and free from any source of flame or sparks this includes any appliance with a pilot light.
8-26 FUEL SYSTEM (DFI) DFI Servicing Precautions DFI Servicing Precautions There are a number of important precautions that should be followed servicing the DFI system. x25CB This DFI system is designed to be used with a 12 V sealed battery as its power source. Do not use any other battery except for a 12 V sealed battery as a power source.
© 2017 Auto&Moto. All rights reserved